比利时的建筑道路，带有3D无弦铺路

作者：Karina Lumholt

阿克拉格罗在比利时，是一家专门从事基础设施项目的公司，目前在比利时和法国雇用350名员工。阿克拉格罗（Aclagro）决定自动化其混凝土滑动铺路机，并选择Leica Geosystems Solutions，因为该公司多年来一直信任Leica Geosystems。

“We were a bit concerned if our workers could learn to work with the new system,”explains Yves De Backer, foreman at Aclagro.“But, after a few weeks, our people were quite familiar with the new system. The machine is now so easy to set up and operate, and the possibilities are almost unlimited.”

该公司的Wirtgen SP15路缘和天沟机配备了Leica图标铺路解决方案与new innovative 1UP configurationfor a road ramp building project in a suburban area in Aalter located between Bruges and Ghent in Belgium. Theworkflow from earthworks to curb and gutter paving went seamlessly。这paving machine came into work just after the excavator had finished the earthworks, and, after data upload, it was ready for the job. This was particularly important because the street residents had no access to their houses during the construction works, and the3D paving solution from Leica Geosystems helped to reduce project time。

Leica iCON pave with 1UP – the best of two worlds

这1UP配置将双GNSS系统与总站和棱镜系统结合在一起。这GNSS system controls the heading of the machine whereas the prism/total station system controls the slope and elevation of the machine’s mould with millimetre precision. This configuration, combining the高精准度总站和Prism配置的整体配置是使用GNSS控制机器方向的GNS的最重要的，并允许客户：

• Simplify the installation
• Reduce the setup time
• Save costs because fewer total stations are needed, and the RTK corrections of the GNSS system are not required.

“对我们来说，最重要的问题是：“系统有多灵活？””says De Backer.“Because of this, we decided to go for a GPS and TPS combination. When working in a tunnel, we use two total stations, but when we are just driving in the open field, we use GPS for the direction and total station for the height.”

Leica Geosystems于20年前发明了3D无弦铺路。Avoiding the physical stringlinesincreases safety on site因为人们不再绊倒弦线，因此现场需要更少的工人。

Designed for even the harshest of environments

这solution included the new ruggedMCP80通过IP66和IP67评级认证的面板，这意味着它是protected against dust and water penetration。这对于没有机舱的路缘和排水沟机器的解决方案以及安装在机器上的面板的解决方案尤其重要，但要遵守诸如铺路工作的典型环境之类的元素。这大型触摸屏is designed for easy navigation andcan be used even in direct sunlight。

Leica MC1用于铺路解决方案

Aclagro的路缘和天沟机的机器控制解决方案已通过新的Leica MC1软件是Leica Geosystems的新一代机机控制平台。MC1是所有软件解决方案指导和自动化所有图标解决方案，导致简化的工作流程。MC1软件现已发布针对整个图标路段的发布，包括土壤压缩机，混凝土摊铺机，沥青摊铺机和铣床。新软件有一个uncluttered and user-friendly interface提出了最重要的功能。

对于路缘和天沟机，面板中的快速访问键允许操作员能够用手指轻松更改高度偏移and without leaving the run screen that has been set up with the exact preference for the operator.

与Leica Conx，基于云的数据共享工具，允许简单的数据传输实时往返机器并为客户提供机会远程支持。

“可以远程检查机器，这对我们来说是一个很大的好处。当我们在工作现场遇到问题时，我们不必损失很多时间。”concludes Yves.

以3D无弦铺路解决方案，诸如自动Leap Frog，1UP配置和新的MC1软件平台（新的MC1软件平台）的技术开发的经验为基础20多年的经验，这证明Leica Geosystems继续为铺路行业提供领先的3D解决方案。